Get The Analogue

2011 E90 335xi N55 crank/no start: Terminal 87_2 fault 00332F

A voltage-first diagnosis for BMW N55 fault 00332F, including relay checks, VIN-specific wiring and safe branch isolation.

By Chase Waters · · 6 min read

A 2011 E90 335xi owner asked about an N55 that would crank but not start while fault 00332F Terminal 87_2: no voltage kept returning. The direct answer is to treat 00332F as a power-distribution diagnosis, not as an automatic DME verdict. Prove the supply path under load, identify the exact Terminal 87_2 consumers from VIN-specific wiring, and isolate the branch before condemning a control unit.

What 00332F is actually telling you

Terminal 87 is switched battery voltage delivered through a relay. The _2 suffix identifies one monitored output or branch in the engine-management supply arrangement. When the DME records no voltage there, it means the voltage it expects on that branch is absent. It does not, by itself, name the failed component.

That distinction matters. A crank-no-start can tempt an owner to replace whatever appears in the fault text. But the missing voltage may be caused by the feed into the relay, the relay contacts, a fuse, a high-resistance connection, a damaged wire, or a load pulling the branch down. A fault inside the DME is possible, but it belongs at the end of a measured test sequence.

BMW's Power Supply training material separates permanent battery power, Terminal 30, from switched supplies. It also explains that fuses and relays can be distributed among several boxes, and that the E90 uses a junction box behind the glovebox. That architecture is why a visual fuse check or a relay click cannot close this case.

The owner discussion that prompted this article included several simultaneous actuator and sensor electrical faults along with 00332F. A cluster like that is useful evidence. Several unrelated components rarely fail at the same moment, so I first look for what their circuits share: supply, ground, harness routing, connector, or control.

Start with voltage, not parts

Before tracing Terminal 87_2, make sure the electrical baseline is sound.

  1. Measure the battery at rest and during cranking. Record the lowest cranking voltage. A charger indication or a recent battery replacement is not a measurement at the moment the fault occurs.
  2. Run a complete vehicle scan. Save the first scan, clear the faults, crank once, and scan again. Separate current faults from history and note which faults return together.
  3. Check constant power at the applicable distribution point. BMW identifies permanent battery voltage as Terminal 30. Verify it with a meter at the circuit you are testing, not only at the battery posts.
  4. Check both sides of each relevant fuse. Do this with the circuit awake or commanded. A fuse can look intact while its holder or feed has excessive resistance.
  5. Measure relay input and output. A bench click confirms coil movement, not clean load contacts. The useful question is whether battery voltage reaches the output while the circuit is carrying current.

A voltage measurement without a known reference can mislead. Use a verified ground, and compare the reading with battery voltage taken at the same time. If a digital meter shows normal voltage but the circuit fails under demand, use an appropriate loaded test or voltage-drop measurement. Do not substitute a high-current test lamp on an electronic control circuit unless the wiring information explicitly supports it.

Measure the positive side and ground side separately. On the feed path, voltage drop between the battery positive post and the powered consumer reveals resistance in cables, connections, fuses, or relay contacts. On the ground path, voltage between the component ground and battery negative during operation exposes a weak ground connection.

Use the VIN diagram and isolate the branch

Do not copy a fuse number, DME pin, wire color, or list of Terminal 87_2 loads from another E90 and assume it applies. BMW changed power distribution with engine, production date, market, and equipment. Even cars that share an E90 badge and N55 engine can require different diagram selections. Start with the VIN, then confirm the connector view and wire color on the car before probing.

Build a simple path from the selected diagram:

battery / Terminal 30 → distribution point → fuse → relay contact → Terminal 87_2 splice → individual loads

Also draw the relay control side separately. Identify the coil feed, the control wire, and which module switches it. This prevents confusing a relay-control pin with the switched output.

Then test the path in order. If voltage enters the relay but does not leave when commanded, investigate the relay and its control. If correct voltage leaves the relay but is absent at the downstream splice or consumer, investigate the connector and harness between those points. If voltage is present unloaded but collapses when connected, suspect excessive resistance upstream or a shorted downstream branch.

Branch isolation is especially valuable when several components share Terminal 87_2. With the ignition off and the battery handled according to BMW service precautions, disconnect one documented branch load at a time. Reconnect power, command the circuit, and watch the relay output and fault behavior. If the supply returns after one branch is disconnected, inspect that component, connector, and its section of harness before replacing anything.

Do not disconnect items at random. Label connectors, avoid spreading terminals, and never probe a connector face with an oversized lead. If recent work preceded the no-start, inspect that work area for a trapped loom, pulled connector, backed-out terminal, coolant or oil contamination, and a ground eyelet left loose.

When the evidence points beyond the harness

The real owner thread ran for months. The owner reported checking power through the fuse path and at the referenced DME connections, then later reported that the installed DME was the fault and showed severe internal damage. That outcome is useful, but it is one case, not permission to skip circuit testing on the next car.

A sound decision requires evidence that the external system can support the module. Confirm the correct permanent feeds, switched feeds, grounds, relay control, relay output, and downstream branch behavior with the circuit connected. Check for corrosion, terminal tension, water entry, and voltage drop. If a known shorted load or damaged harness caused an overcurrent event, repair that root cause before installing another module.

If the external circuit tests correctly and the DME still fails to command or recognize the supply, stop at module-level diagnosis. Do not open or attempt circuit-board repair. Use a qualified automotive electronics specialist, and provide the VIN-specific diagram, saved scans, voltage measurements, and the event that preceded the failure. That record is far more useful than a box of replaced parts.

Frequently asked questions

Does 00332F prove that the DME has failed?

No. It proves that the monitored supply condition was not present when expected. Test the whole path before treating the DME as the cause.

Is a relay good if it clicks on a bench test?

No. The coil may operate while the contacts remain resistive or fail under load. Measure the switched output in the installed circuit.

Which loads are always on Terminal 87_2?

There is no reliable universal E90 N55 list. Retrieve the diagram by VIN and production data, then verify it against the connector and wire colors in front of you.

What is the fastest safe first test?

Measure battery voltage during cranking, rescan after one crank attempt, and compare Terminal 30 relay input with the Terminal 87_2 output under the same condition. That quickly separates a low-voltage problem from a missing switched branch, while leaving the detailed diagram to identify why the branch is missing.

Questions owners ask

Does 00332F prove that the DME has failed?

No. It reports a missing monitored supply. The cause can be upstream power, a fuse or relay path, wiring, a shorted load on the branch, a connector problem or, only after those are proved good, a DME-side fault.

Is a relay good if it clicks on a bench test?

No. A click only shows that the coil moved the mechanism. Test the switched contacts and measure voltage at the load while the circuit is commanded and carrying current.

Which components are powered by Terminal 87_2 on every E90 N55?

There is no safe universal list. Production date, market and equipment can change the wiring. Use the wiring diagram and fuse assignment selected by the car's VIN.

What should I test first on an N55 that cranks but will not start with 00332F?

Confirm battery voltage during cranking, then follow the VIN-specific circuit from constant battery power through the relevant fuse and relay to the monitored Terminal 87_2 branch.

Sources

  1. BMW Technical Training, Power Supply
  2. Bimmerfest owner discussion, page 1
  3. Bimmerfest owner discussion, page 2
  4. Bimmerfest owner discussion, page 3 and reported outcome