Get The Analogue
Diagnostics · BMW E60, BMW E61, BMW E82, BMW E83, BMW E85, BMW E86, BMW E90, BMW E91, BMW E92, BMW E93

BMW N52 Long Crank After 5 to 10 Minutes: Should I Test Coils and Plugs?

Diagnose an N52 long crank after a short hot soak by testing fuel-pressure retention, cranking speed, voltage, and engine-speed data before parts replacement.

By Chase Waters · · 5 min read

An N52 that starts immediately after shutdown but cranks long after sitting for five to ten minutes presents a timing pattern worth testing. Coils and plugs can be inspected, but they are not my first parts choice when the engine runs normally after it starts. I begin with fuel-pressure retention, cranking voltage, starter speed, and the engine-speed signal, then let the failed test choose the next component.

Would it be worth testing coils and plugs too?

Yes, but not by replacing a complete set before checking the pattern. The owner question came from a 2009 328xi that started normally if restarted within about two minutes, then cranked long after a five-to-ten-minute soak. The battery and alternator had already been replaced. The owner wondered whether coils, plugs, a leaking injector, the fuel-pressure regulator, or battery wiring might be responsible.

Forum participants focused on fuel-pressure bleed-down, and one owner with a similar 328i reported that pressure dropped almost immediately after shutdown. Replacement of the sending-unit and pump assemblies resolved that owner's complaint. Another participant reported an eventual crankshaft-sensor diagnosis. Those are independent outcomes, not proof of one universal cause.

BMW fuel-management training provides the system map. On the N52 example, the electric pump sends fuel through check valves and the fuel filter to a 5 bar pressure regulator before fuel reaches the engine. The DME also uses battery voltage and crankshaft position or engine speed when controlling injection. A short-soak long crank can therefore be approached with measurable checks instead of a parts list.

Test pressure retention during the exact waiting period

First measure fuel pressure while the car starts normally, immediately after shutdown, and through the five-to-ten-minute interval that produces the long crank. Use the correct gauge, adapter, and safe procedure for the exact model. Some scan data can show useful system values, but a mechanical measurement may be needed to confirm what is physically happening at the rail.

BMW's training diagram shows two check valves in the E9x fuel-supply layout, along with the in-tank pump, filter, and regulator. If pressure falls too quickly, the possible leak path has to be isolated. A check valve can allow fuel to return. A regulator can fail to retain pressure. An injector can leak into a cylinder. An external leak also has to be ruled out immediately.

Do not decide which part failed from pressure decay alone. Inspect for external fuel odor or wetness without creating a spark source. If injector leakage is suspected, use an appropriate test and inspect for evidence in a controlled way. Repeatedly cranking a fuel-loaded cylinder risks oil dilution and catalyst damage.

The most useful comparison is repeatable: note pressure at shutdown, after two minutes, after five minutes, after ten minutes, and during the next crank. If the long crank begins only after the same pressure drop, the pressure-retention path becomes much stronger.

Check voltage, cranking speed, and engine-speed data

A new battery or alternator does not prove that voltage remains healthy at the DME and starter during crank. Record battery voltage from before the start command through cranking. Listen for a consistent starter speed and compare engine rpm in live data. A slow starter can reduce cranking speed even when resting battery voltage looks acceptable.

BMW training states that injection duration is adjusted for battery voltage because injectors react more slowly at lower cranking voltage. The document also states that the DME needs a crankshaft position or rpm signal to maintain fuel-pump activation and trigger injection. That makes the rpm trace important.

Look for:

  • engine speed appearing immediately when the starter turns
  • a stable cranking-rpm pattern rather than sudden dropouts
  • voltage that remains consistent across normal and long-crank starts
  • fuel-pump operation continuing while the DME sees engine speed
  • any pending or shadow faults related to engine speed, voltage, or fuel delivery

A crankshaft sensor can be intermittent before a clear code appears, but it should be tested through the signal and symptom pattern. A missing or erratic rpm value during the long crank is stronger evidence than replacing the sensor because another owner eventually found one faulty.

Use ignition and mixture evidence after the basic split

If pressure retention, cranking voltage, starter speed, and rpm signal all pass, then inspect plugs and ignition components. Remove plugs after reproducing the complaint only when safe and appropriate. Compare all cylinders. One wet or unusually clean plug can direct attention toward an injector or cylinder-specific problem. Uniform plug condition makes a single-cylinder leak less obvious but does not end the test.

Coils usually reveal themselves through a misfire under startup, idle, or load rather than only by extending starter time with clean running afterward. Check pending misfire counters and cylinder roughness immediately after the engine catches. Swap one suspect coil only when one cylinder repeatedly stands out. Changing six parts at once removes the ability to identify the cause.

Also compare coolant temperature with actual engine condition. An implausible temperature input can alter starting fuel. Inspect intake integrity if fuel trims or post-start idle behavior show a lean pattern. Keep each test tied to evidence from the failed start.

Verify the repair across the full soak window

A repair is not confirmed by one immediate restart. Repeat starts after two, five, ten, and twenty minutes, plus a cold start the next day. Record the same pressure, voltage, and rpm values each time. The original five-to-ten-minute failure window must pass consistently.

If a pressure-retention repair was made, confirm that pressure now holds through the interval and rebuilds promptly during crank. If an electrical repair was made, verify voltage at the affected circuit under starter load. If a crankshaft-signal problem was corrected, confirm a clean engine-speed trace on every attempt.

Check current, pending, and shadow faults after the test series. Watch the first seconds of idle for misfires or rich exhaust odor. Recheck engine oil if fuel contamination was suspected.

The answer to the owner's coil-and-plug question is therefore conditional. Inspect them when cylinder evidence points there, but start with the measurements that match the repeatable soak-time pattern. Pressure retention, cranking voltage, starter speed, and engine-speed data can divide this complaint into a much smaller and more defensible set of causes.

Questions owners ask

Would it be worth testing coils and plugs too?

They can be inspected, but a repeatable long crank only after a five-to-ten-minute soak should first be checked for fuel-pressure retention, cranking voltage, and a stable engine-speed signal. Test the system that matches the timing pattern before replacing ignition parts.

Can an N52 lose fuel pressure after shutdown and still run normally once started?

Yes. A check-valve or regulator problem can allow residual pressure to decay, while the pump may still supply enough fuel after pressure is rebuilt.

What fuel pressure does BMW describe for the N52 system?

BMW fuel-management training identifies a 5 bar pressure regulator for the N52 example. The same document shows check valves, the filter and regulator, and the in-tank pump in the supply path.

Can a crankshaft-position sensor cause a long crank without an immediate code?

A marginal signal remains possible. Check whether engine speed appears promptly and steadily during the failed start, because BMW training states that the DME needs the crankshaft-speed signal to maintain pump operation and trigger injection.

Sources

  1. Bimmerfest owner question: N52 long crank after a five-to-ten-minute soak
  2. BMW technical training: N52 fuel supply, check valves, regulator, and starting inputs