Get The Analogue

BMW N52 2A87 and Heavy Smoke: Does One Explain the Other?

A BMW N52 2A87 fault points to an exhaust VANOS movement problem, but it does not prove why the engine is smoking. Separate both diagnoses safely.

By Chase Waters · · 5 min read

Not by itself. I treat 2A87 and heavy smoke as separate findings until tests connect them. BMW's service information identifies 2A87 as an exhaust VANOS camshaft fault, but the code does not prove why an N52 is producing heavy smoke or oil in the exhaust. If smoke is heavy, stop the engine when safe and arrange a tow rather than running it to capture more data.

N52 Random white smoke and 2A87 code: does one explain the other?

BMW Service Information SI B11 02 08 lists 2A87 as an exhaust VANOS fault described as stiff or mechanically jammed. It also lists related camshaft-position faults where the requested position is not reached. The bulletin covers several BMW models and engines, including E60/E61 cars with N52, N52K and N54 engines. It describes power reduction after the engine reaches operating temperature as one possible situation. Check the bulletin's model and production-date coverage against the VIN before applying its procedure.

The bulletin does not say that 2A87 causes oil to enter the exhaust. It says VANOS faults can arise from insufficient oil-pressure supply to the adjustment unit, and that a mechanical restriction or an electrical failure in the solenoid or circuit can also cause inadequate oil supply. The procedure starts with completing the applicable BMW test plans. It does not support replacing parts based on the code alone.

A BimmerFest owner with a 2007 525xi reported rough idle, 2A87, heavy smoke from under the bonnet and exhaust, and oil in the exhaust. Cleaning and changing solenoids seemed to help briefly, then the symptoms returned. That is a real case report, but it is not proof that the VANOS fault caused the smoke or that the same fault path applies to another car.

Separate smoke triage from the VANOS test

I first record where the smoke appears: under the bonnet, at the tailpipe, or both. Note whether it begins cold or hot, whether it follows idling or acceleration, and whether it returns after a short drive. Do not identify the source by colour alone. The BimmerFest report describes a combination of smoke and 2A87; it does not establish a general cause for that combination.

If smoke is dense, persistent or accompanied by a falling oil or coolant level, switch off when safe and do not continue driving. If you see flames or a fire risk, move away and contact emergency services. Do not open a hot cooling system or reach near belts, fans or a hot exhaust. A scan is useful only when the car can be operated safely. With severe active smoke, arrange recovery first.

When the car is cool and safe to inspect, document fluid levels using the owner's manual procedure and look for visible external leaks without removing hot components. Keep the smoke location and the fluid observations separate from the DME code. Oil on a hot external surface, oil entering an intake or exhaust path, and coolant vapour require different checks. The report of oil in a tailpipe is a reason to inspect, not a confirmed diagnosis of where that oil came from.

Follow the VANOS and crankcase test plans

Save a full DME scan before clearing anything. Confirm the engine and DME variant by VIN, record every related code and note whether the fault is current or stored. Follow the BMW test plan for the exact combination. SI B11 02 08 says to complete applicable test plans and notes that a mechanical restriction or electrical failure at the solenoid or circuit can affect oil supply. Check the oil and filter service history and inspect the filter housing components called out by the vehicle-specific procedure. Do not replace both solenoids unless that procedure and the test results support it.

If the symptoms include oil consumption, oil in the intake or rough idle, add a separate crankcase-ventilation check. BMW SI B11 03 08 explains that excessive crankcase pressure or vacuum can be associated with increased oil consumption and oil in the intake system; excessive vacuum can also be associated with rough idle or misfire. That makes a measured test more useful than guessing from smoke colour. It does not establish that ventilation caused the smoke in the BimmerFest case.

BMW's 2018 bulletin lists 30 mbar for N52 and 33 mbar for N51/N52K. It also says readings can vary with the instrument and describes a BMW measurement method. Those figures are not interchangeable across variants or tools. Confirm the engine code and use the specified procedure and equipment before comparing a reading with a limit. Do not borrow a number from another BMW engine or a generic hand-held gauge.

For the VANOS fault, compare camshaft target and actual behaviour only through the correct diagnostic test plan and under its stated operating conditions. Record whether the fault returns and whether the exhaust cam reaches the commanded position. Avoid improvised revving with active smoke or a hot engine. If the oil supply, electrical circuit or mechanical VANOS checks remain inconclusive, escalate to a technician with the BMW test plan and the saved scan rather than guessing at the next component.

Keep the conclusion tied to measured evidence

The two symptoms may share a cause, or they may be separate faults. The available owner report cannot settle that question. A valid conclusion needs evidence from the smoke-source inspection, fluid condition, correct crankcase-pressure test where indicated, and the BMW VANOS procedure. If one test confirms a fault, record the measurement and repair, then recheck the same symptoms and DME codes under safe conditions.

The distinction matters because a temporary improvement after cleaning or replacing a solenoid does not explain a return of heavy smoke. Nor does the presence of oil in the exhaust identify which engine system introduced it. Keep the scan, test results and smoke observations in one timeline so a technician can see what changed and when.

FAQs

Does 2A87 explain heavy smoke from an N52?

Not on its own. BMW defines it as an exhaust VANOS camshaft fault, but it does not identify the source of smoke or oil in the exhaust. Diagnose both findings and connect them only if test results support that conclusion.

Should I keep driving with heavy smoke and 2A87?

No. If smoke is heavy or a fluid is escaping, stop the engine when safe and arrange a tow. Do not keep the engine running for live data while the smoke source is unknown.

What crankcase-pressure value should an N52 show?

BMW SI B11 03 08 lists 30 mbar for N52 and 33 mbar for N51/N52K, but the correct value depends on the engine variant and BMW procedure. The bulletin also warns that readings vary by measuring tool. Verify the VIN and use the specified method.

Questions owners ask

Does 2A87 explain heavy smoke from an N52?

Not by itself. BMW service information identifies 2A87 as an exhaust VANOS camshaft fault, but the code does not establish the source of smoke or oil in the exhaust.

Should I keep driving with heavy smoke and 2A87?

No. If smoke is heavy or fluid is escaping, stop the engine when safe and arrange a tow. Do not keep running the car to collect live data.

What crankcase-pressure value should an N52 show?

BMW's 2018 bulletin lists 30 mbar for N52 and 33 mbar for N51/N52K, and warns that readings vary by tool. Confirm the engine variant and follow the BMW measurement procedure for the car.

Sources

  1. BMW Service Information SI B11 02 08: 2A82 intake and 2A87 exhaust VANOS faults
  2. BMW Service Information SI B11 03 08: crankcase ventilation diagnosis and measurement
  3. 2007 BMW 525xi owner report: random white smoke and 2A87